[02:10:27] Hi [02:46:40] #KSPOfficial: mode change '+v eriophora' by ChanServ!ChanServ@services.esper.net [11:27:30] https://cdn.discordapp.com/attachments/429717171002933269/571281223977140245/DSC_1205.JPG [11:57:49] Fluburtur: are you just hammering them in? [11:57:55] yeah [11:58:04] with a piece of wood to not put them out of shape [11:58:12] also I put a bit of white glue in the slot just in case [11:59:21] now I have to find some sort of snipers that are flush on one side [12:00:52] I really hope I wont have to adjust the frets height [12:11:55] nightmare traffic lol https://www.youtube.com/watch?v=fuS6R2KZuQ8 [12:11:56] YouTube - I was Made Mayor to Fix NIGHTMARE Highways in Cities: Skylines [12:26:35] why am I bleeding out of my fingers [12:26:50] have I being using the metal files too much? [12:26:53] because you were sanding them instead of the wood? [12:27:11] man take it easy there man [12:27:12] might be why yeah [12:27:22] because my files dotn have handles [12:27:27] lol [12:27:37] at least use some cloths to hold them [12:27:52] no I will put tape on my fibers [12:28:06] sticky tape :) [12:28:40] do it in layers, use masking tape for a bit, then finally rubber tape for hand confort on files [12:29:39] 5 layers of paper tape [12:31:54] there is blood on my bass now [12:32:05] why am I bleeding everywhere [12:32:15] you have blood thats why [12:32:19] maybe make the blood a part of it [12:32:38] embed a small glass vial with blood in it in the frame [12:32:43] well my previous guitar also had blood in it [12:33:16] actually im probably bleeding there because I cut myself on the frets I cut [12:33:22] those are very sharp [12:40:59] sharp frets are the worst [12:42:30] dont fret, the frets cut his hands :) [12:42:38] not yours [16:43:12] https://cdn.discordapp.com/attachments/429717171002933269/571360690619678730/DSC_1219.JPG [18:00:41] #KSPOfficial: mode change '+o UmbralRaptop' by ChanServ!ChanServ@services.esper.net [18:52:51] #KSPOfficial: mode change '+o UmbralRaptor' by ChanServ!ChanServ@services.esper.net [18:53:24] scott about marsquake [18:59:01] #KSPOfficial: mode change '+o UmbralRaptop' by ChanServ!ChanServ@services.esper.net [19:36:38] https://cdn.discordapp.com/attachments/416068486167658497/571403862427303966/DSC_1223.JPG [19:37:32] https://www.youtube.com/watch?v=nQjPcvNHT5E [19:37:32] YouTube - Deep Purple - Somebody Stole My Guitar (Purpendicular 11) [20:14:38] I need a long and thin drill bit and I dont have any [20:19:01] Take out the mill and make one... [20:19:03] Action: Mat2ch hids [20:19:06] *hides [20:19:50] im trying to drill with a sharp screwdriver [20:32:29] This Friday is so slow, I'm listening to Supertramp and Status Quo... [20:32:35] Could be worse [20:32:47] but also much better :P [21:06:47] #KSPOfficial: mode change '+o UmbralRaptor' by ChanServ!ChanServ@services.esper.net [21:11:07] #KSPOfficial: mode change '+o UmbralRaptop' by ChanServ!ChanServ@services.esper.net [21:11:41] #KSPOfficial: mode change '+o UmbralRaptor' by ChanServ!ChanServ@services.esper.net [21:12:49] #KSPOfficial: mode change '+o Raptop' by ChanServ!ChanServ@services.esper.net [21:15:16] #KSPOfficial: mode change '+o UmbralRaptop' by ChanServ!ChanServ@services.esper.net [21:47:35] Last message repeated 1 time(s). [21:47:35] #KSPOfficial: mode change '+o UmbralRaptor' by ChanServ!ChanServ@services.esper.net [22:58:33] Action: darsie could orbit Eeloo but doesn't have enough fuel to land. [23:32:07] Fluburtur: https://www.youtube.com/watch?v=1I_EPkHqU20 [23:32:08] YouTube - Look Mum No Computer playing dance classics on a Furby organ [23:32:19] almost a year old, but just stumbled upon it [23:32:25] https://youtu.be/81UjjSH2iFw [23:32:25] YouTube - WFL M60 MillTurn Complete Crankshaft Machining - MARTECH Machinery, NJ - USA [23:33:18] Oh, I think I've seen that one. :D [23:34:37] Massproduced crank shafts are today pressed (in almost molten state) and then just slightly machined for the end finish [23:34:55] it is a luxury or sport car one [23:35:12] yeah, for small amounts that's cheaper :) [23:35:22] also do not play with the scraps without gloves :D [23:37:05] if I'd get another axis, I could do this with my cnc. But in small scale only ;) [23:40:45] (and yes, there are people doing this for small engines... Crazy stuff) [23:41:02] https://youtu.be/onE8jKwtX8I?t=49 [23:44:03] Fluburtur: I wouldn't want to be anywhere near that thing without a shield [23:44:33] it is a bit powerful as well, needs a large plane [23:44:53] someone on my server wanted to build a tiny radial and I offered to help in the desing [23:49:38] well, I'm more the going-electric person... [23:50:08] and the "going to bed now" person ;)